Видео

Average Pubg player phone

Thank you sincerely for your insightful guidance on designing an ESC. I highly recommend exploring the ARM Cortex-M based STM32 microcontrollers as a next step; their robust capabilities could significantly enhance your projects. Your teachings have been incredibly valuable, and I am confident that your continued exploration will lead to even greater innovations. Thank you once again for your mentorship.

Where the heck am I supposed to get a 100 milihenry (mH) inductor? I HOPE you mean 100uH. I dont think the one in your video is 100mH with that few of turns - but clearly it is high Q given the wire size - I mean trying to buy one from like Mouser is $46 for a 1A and it looks like a small transformer. Also on some of your schematics on your website, you have some of your FETs the wrong way (forward biasing the body diode). That would suck if you hooked it up that way LOL.

Dont be ashamed! Really fascinating and candid insight into a good tech youtube channel! I have like 8 YT channels with like a couple hundred subscribers TOTAL... yet many hundreds of educational videos. Not monetized, was always worried about someone shutting me down by clicking multiple times on an ad or some BS. I do think your idea to move into the countryside is a good one - perhaps one day. Good luck!

Finally I can at least become level 4 Esper

I am desperately waiting your next MPPT project.

Hi, can you let us know the model and maker of the Fiber Laser you using? And thanks a lot for the very good job on clearing the subject.. I was just trying to find a good way to make good home made PCBs and definitly this fiber laser is the answer

adding a resistor to discharge the capacitor after turning off the gun could be great security too; never know if the capacitors are not fully discharged after the shot

Water + Electricity , nice combination 😂

cool video (or hot ;) ) . Is there a link to that mega resistor? I have similar ones but smaller. I used plaster of paris mix with a little bit of fine sand. for my furnace. easy to find in store and simple to work with. Although it is not a strong as a real ceramic.

May you please tell me how to connect potentiometer in circuit.??

How to tune this pid values .can you please put tutorial on that

🙏🙏

irresistible

Better to implement a brake and when battery is fully charged we just apply the brake and prevent the turbine from rotating. One could also add controlable angle of the turbine blades to reduce the forces on the turbine when not rotating in strong winds

What about just short the wind turbine if the battery is fully charged and the turbine is only outputting low voltage (when there's barely any wind) so it ends up being that the eddy currents resist and stop the turbine from spinning

the first of the two integrates used will balance 16 cells, while the other will balance 10 cells, and you know how these circuits can be connected to each other, please can you help

Great explanation!

Buy a bag of big old NPN power transistors, they are available very cheap now as they are obsolete technology. Big flat pack transistors are good for about 65w each if bolted to a big slab of metal. You can probably get 20 transistors for 20 dollars. That gives you an additional benefitmof being able to control them, ie ADJUSTABLE load

Apologies if this has been suggested before, but why don't you incorporate a TEG and use the excess heat from the resistor for extra power?

MOB FOR YOU INVERTER PROJECT PLEASE MY FRIEND

I make high power resistors myself from nichrome wire for diy project XD its not so easy or cheap to get a multiple hundret watt rated resistor at less than a couple ohms

אתה רעעעעעעעעע

el threadlocker es para pegar 2 metales y evitar que se desenrosquen con el uso o las vibraciones, por ejemplo se usa en varios tornillos de una bici, pero no es indicado para pegar metal con teflon, quizas ni se endurezca, tampoco esta pensado para estar en contacto con el agua. Una opcion podria ser utilizar solo teflon, o usar una aleacion de estaño con un punto de fusion bajo y calentarlo muy rapido, tambien puedes sellarlo por fuera con cinta autosellable para fugas

hello ,can you upload the BOM excevl for you project at inverter ,thanks a lot

23 and no tests 😢

Wich module can I use to measure current with a node mcu and a solar panel 12v 10a ? Thanks

I liked it, tell me the laser power?

This is a great video!

You also may use a heater which may easily dissipate 2-6 kW and also heat utility water. Besides of being dead cheap.

Thank you ! Great explanation !

You could use many small resistors in parallel.

blasphemie

Help us to bulid the project with different concept will you?

Plastic is not a megaohm conductor. Not even gigaohm. Please try again.

Can you share the PCB altium shematic and components you used, I want to use it in my project.

You made my arduino journey thank you ❤

A clothes washing machine with direct drive is typically free and over 3x the size of those motors

Another idea is to find an amateur potter and get them to make some tubes and fire them for you.

I had a wind turbine and its resistor was a thick wire about 5mm thick. And to stop the turbine when working on it the resistance was a solid bar of aluminum shorted across the terminals

I made a pair of heated gloves from ni-cr wire. It worked well but only had on off switch so was some times getting hot.

Hello try laser cut steel from jlpcb make a nece add and a good variable resistor

Cuando haras un welder inverter?

Cuando haras un welder inverter?

Do some larger wind turbines have mechanical brakes to prevent over spinning? It seems like this could be an alternative way of slowing the turbine shaft in a fully charged/high wind condition.

Please Electronob wich is the software that you used for animations ? thanks

Dump the energy to a water heater as a resistor

That was painful to watch... First of all that insulating tape will burn to crisp when that 'resistor' gets any substantial amount of power. You could have used lightbulbs, water heater elements, just dunked that wire into a bucket of water, steel wire or tape.

Daigram plzzz

Careful, one guy who made this got poisoned.